FAQS

CABLECRAFT

Frequently Asked Questions

Find answers to commonly asked questions about our products.

CABLES

To allow installation for different applications (i.e. push-pull or pull-only). There are various constructions and engineered materials to meet specific customer requirements made by Cablecraft®.

Yes, approximately 80% of our business is custom-designed controls.

Yes, we have a specific aircraft product line for home-built as well as certified aircraft.

Our main discerning difference is the ability to install our controls in a much tighter bend radius than our competitor’s controls. Because of our association with aircraft, ordnance and industrial applications, we are able to utilize technical advances across all product lines.

Our design, unlike most of our competitors, is decreased efficiency as opposed to failure due to separation. Our design doesn’t fail without warning to the operator.

Yes, there are load capability diagrams to aid in specific application selections. Catalog loads are not specific for all applications but should be treated as guidelines. Contact an engineer for advice.

Yes, we have 55+ years of application design experience. Contact Sales for suggestions.

Please complete the Contact Us form and an engineer will be in contact shortly.

LINKAGES

The load is applied along the axis of the ball bore or ball stud.

The load is applied along the axis of the female housing or male shank.

This is a measurement of the total range of movement of the ball in the cavity in the axial direction or the clearance measured along the axis of the bore and ball stud.

This is a measurement of the total range of movement of the ball in the cavity in the radial direction or the clearance measured along the axis of the female housing or male shank.

Using a load cell the rod end is secured by placing a pin horizontally through the ball bore and securing it to a test block. The threads on the housing or shank are fastened to a pull rod. The part at this point is in a vertical position with the head secured. The rod end is then pulled until failure in the radial direction.

The shank or housing is slip fit into a collar in the horizontal direction. A pull rod is then placed through the ball bore. The rod end ball is then pulled in the axial direction until it is removed from the rod end housing.

A lubricated fiberglass reinforced nylon is used.

0.2% (data acquired from supplier catalogs per ASTM Test D570 for 35-45% glass fill).

The rod ends may be continuously run in a range from -30°F to 220°F (-34°C to 104°C).

Nuts may be torqued to a Grade 2 SAE torque specification for the appropriate thread size.

All zinc plated rod ends and ball joints are plated per ASTM B633. Typically, red rust develops after 96 hours of salt spray testing for zinc coated parts with clear dichromate.

Yes, we offer a wide variety of linkage assemblies and custom linkage components including a wide variety of double ended connecting rod assemblies. Please contact a Cablecraft representative to find out more.

Ball joints are typically used in an application where the axial and radial play are not as critical. A rod end may also come in the studded or non-studded form, where a ball joint is constructed of a housing and a one piece ball stud. Ball joints are typically less expensive than rod ends. Rod ends would be recommended for a higher load and precision application.

Listed in the Cablecraft catalog are radial (tensile) test load values. On a majority of these products, axial (ball pullout) and wear tests have also been performed. To see if data that interests you is available refer to the information in our product catalog. If the data you need is not there, you can contact a member of the Cablecraft Engineering staff.

Please complete the Contact Us form and an engineer will be in contact shortly.

Engineering Resources & Design Guides  

Our engineering team has applied their years of industry experience to develop resource documentation for each of our product lines.

GO »

Cable Assembly Network  

Our Worldwide Cable Assembler Network can help you with your mechanical motion control solutions.

GO »

Online Catalog  

Don’t need a custom design? Download our digital catalog to see all of our available cable and linkage assemblies.

GO »

REQUEST A QUOTE

If you already know what type of product and application you need, fill out the full form below and we’ll get started on providing you with the highest quality engineered cable and linkage solutions on the market. Still trying to decide how we can help you? Just enter your contact information below and we’ll be in touch to set up an initial call.

Attach files by dropping them in here, or You can also [browse your computer]

Your browser does not support HTML5 uploads. Please update to a newer version.